WARNING: ENSURE YOUR FIREARM IS UNLOADED BEFORE ADJUSTING YOUR SIGHT. AT ALL TIMES FOLLOW THE BASIC FIREARMS SAFETY RULES IN THE SECTION ENTITLED YOUR SAFETY RESPONSIBILITIES.WARNING: VISIBLE LASER RADIATION EMITS FROM THE CRIMSON TRACE® LASER WHILE IT IS IN OPERATION AVOID DIRECT EYE EXPOSURE. Mount a target with a clearly visible aiming point downrange at the desired zeroing distance.
Jun 28, 2015 - Walther's PPK and PPK/S are timeless. You can accomplish a lot with dry fire training, of course, but there's no. SPECS: Walther PPK/S.
Turn ON the Crimson Trace® Laser by pressing the activation button once. While aiming the M&P® BODYGUARD® 38 revolver with its iron sights, rotate the adjustment screws as needed to superimpose the laser strike point over the M&P® BODYGUARD® 38 revolver’s aiming point. To determine the required direction of rotation, refer to the Laser Adjustment Table on page 37 of the owner's user manual. Direct the Crimson Trace® Laser at the target aiming point. Fire a 3-round shot group and note the center of the shot group relative to the target aiming point. Rotate the adjustment screws (FIGURES A10 & A11 see owner's user manual) as needed to move the center of the shot group to the target aiming point. To determine the required direction of rotation, refer to the Shot Group Movement column in the Laser Adjustment Table on page 37 of the owner's user manual.
Fire another 3-round shot group to confirm zero. Repeat these steps until the shot group falls within an acceptable radius around the target aim point. WARNING: ENSURE YOUR FIREARM IS UNLOADED BEFORE ADJUSTING YOUR SIGHT. AT ALL TIMES FOLLOW THE BASIC FIREARMS SAFETY RULES IN THE SECTION ENTITLED YOUR SAFETY RESPONSIBILITIES.WARNING: VISIBLE LASER RADIATION EMITS FROM THE CRIMSON TRACE® LASER WHILE IT IS IN OPERATION AVOID DIRECT EYE EXPOSURE.
Mount a target with a clearly visible aiming point downrange at the desired zeroing distance. Turn ON the Crimson Trace® Laser by pressing the activation button once. While aiming the M&P® BODYGUARD® 380 with its iron sights, rotate the adjustment screws as needed to superimpose the laser strike point over the M&P® BODYGUARD® 380’s aiming point (FIGURE A11). To determine the required direction of rotation, refer to the Laser Adjustment Table on page 46 of the owner's user manual. Direct the Crimson Trace® Laser at the target aiming point. Fire a 3-round shot group and note the center of the shot group relative to the target aiming point.
Rotate the adjustment screws as needed to move the center of the shot group to the target aiming point. To determine the required direction of rotation, refer to the Shot Group Movement column in the Laser Adjustment Table on page 46 of the owner's user manual. Fire another 3-round shot group to confirm zero. Repeat these steps until the shot group falls within an acceptable radius around the target aim point.
WARNING: ENSURE YOUR FIREARM IS UNLOADED BEFORE ADJUSTING YOUR SIGHT. Use only commercially manufactured ammunition with internal ballistic pressures which are in strict accordance with the specifications of the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI).Be certain all ammunition you use complies with the SAAMI specifications.
If you are uncertain, contact your ammunition supplier for verification.If you would like any further information on specific ammunition, you may contact one of the major ammunition manufacturers from the link listed below. Limited Lifetime Warranty: The product is warranted to the original consumer purchaser, for as long as he or she lives, against defects in materials, manufacture of assembly. Damage due to abuse, misuse or neglect is not covered. Defective products will be repaired or replaced. Discontinued items that are not repairable will be exchanged for items of equal value.
In order to get service under this warranty, send the product prepaid, together with an explanation of the defect to the address listed below. Please add $6.95 for return freight.
It is recommended that you insure the defective products to be returned.Smith & Wesson Knives will not be responsible for any damages for loss or use of defective products or for other consequential or incidental damages.BTI ToolsAttn: Warranty and Repair2501 Lemone Industrial BlvdColumbia, MO 65201. Smith & Wesson discontinued manufacturing air and pellet guns in 1980. The air and pellet gun line included the models: 77A, 78G, 79G and 80G.
Should your Smith & Wesson air gun require parts and/or repairs, please contact:Bimrose Precision Airgun Repair is now located at:13090 Navajo Road #3Apple Valley, CA 92308(760) 646-9108TMac's Airgun ServiceC/O Tony McDaniel1120 Finger Bridge RoadHickory NC 28602(828) 294-2468Models 586 and 686 pellet guns, please contact:Umarex USA, Inc.6007 S 29th StreetFort Smith, AR 72908(479) 646-4210We suggest that you call before shipping your air gun to ensure they have the required parts.